do not scale from this print .200 ref 5.08 .040 1.02 ref .220 ref 5.59 .100 ref 2.54 .025 sq ref 0.64 .130 3.30 (no. of pos. -1) x .100[2.54] (no. of pos. x .100[2.54]) + .075[1.91] .100 (typ) 2.54 2 max sway (typ) c 02 (no. of pos. x .100[2.54]) +.160[4.06] ref .300 7.62 .025 sq 0.64 ref (typ) .100 2.54 (typ) (no. of pos. -1) x .100[2.54] 2 max sway (typ) "a" "a" see note 8 c c c ipl1-xx-sh see note 10 see note 7 .215 5.46 .214 5.44 .067 1.71 45 2 max toe (typ) wt-28-03-t t-1s64-09-xxx c section "a"-"a" scale 2.5 : 1 .006[0.15] ipl1-1xx-xx-xxx-sh-k-xx no of positions -02 thru -25 row specification -sh: single horizontal lead style -02: single horizontal .062 board (use t-1s64-09-xxx) -03: single horizontal .093 board (use t-1s64-09-xxx) plating specification -f: flash selective (use t-1s64-09-f) -l: light selective (use t-1s64-09-l) -s: selective (use t-1s64-09-s) -stl: selective tin/lead(use t-1s64-09-stl) polarization -k: keyed polarization -tr: tape & reel (see note 9) option b c c c fig. 1 (ipl1-110-02-xxx-sh-k shown) 01 c b sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .005 [.13] .xxxx: .0020 [.051] material: .100[2.54] single row terminal assembly by: ipl1-1xx-xx-xxx-sh-k-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d. schmelz 10/31/2008 2 1 sheet scale: 2:1 insulator: lcp, color: black terminal: phos bronze f:\dwg\misc\mktg\ipl1-1xx-xx-xxx-sh-k-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. minimum terminal / weld tab retention: 1.0lb. [4.4n] 3. parts to be molded to position. 4. post must be within .005[0.13] of each other. 5. all pin to pin dimensions to be measured from tip to tip. 6. dimension to be measured at bend. 7. tip to be flush to .010[0.254] below top of shroud. 8. this number represents the number of positions per row only and is not intended to be used in position numbering. 9. parts to be packaged in tubes if tape & reel is not specified. 10. indention from weld tab carrier is allowable. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision b
"a" wt-28-xx-x c .530 13.46 ref .215 5.46 ref .240 - .010 + .000 6.10 - 0.254 0.000 t-1s64-09-xxx c c pt-1-24-01-106 in-process 1 fill weld tab in-process 2 fill t-1s64-09-xxx fig. 2 (ipl1-125-02-xxx-sh-k shown) (different as shown, otherwise same as fig. 1) packaging view (parts to have position #1 loaded in same direction as arrow on tube) b sheet of .100[2.54] single row terminal assembly by: ipl1-1xx-xx-xxx-sh-k-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d. schmelz 10/31/2008 2 2 sheet scale: 2:1 revision b f:\dwg\misc\mktg\ipl1-1xx-xx-xxx-sh-k-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
